Difference between revisions of "DIY Lil' CNC"

From i3Detroit
Jump to: navigation, search
m
(Added info about Dremel tool)
Line 9: Line 9:
 
| StorageLocation = In the center of the shop near the [[Torquecut]].
 
| StorageLocation = In the center of the shop near the [[Torquecut]].
  
| MakeModel = Built from [http://diylilcnc.org/ DIYLILCNC] plan version 1.0.3
+
| MakeModel = Built from [http://diylilcnc.org/ DIYLILCNC] plan version 1.0.3; the Dremel tool is a [http://www.dremel.com/en-us/Tools/Pages/ToolDetail.aspx?pid=300+Series 300 Series].
  
 
| Documents = [http://www.linuxcnc.org/content/view/5/5/lang,english/ EMC2 Documentation]
 
| Documents = [http://www.linuxcnc.org/content/view/5/5/lang,english/ EMC2 Documentation]
Line 43: Line 43:
 
* Can I drill printed circuit boards on this thing?  Yes!  Basically, you just need to translate your drill file to the ''lingua franca'' of the mill, [http://www.linuxcnc.org/docview/html/gcode_overview.html G code].
 
* Can I drill printed circuit boards on this thing?  Yes!  Basically, you just need to translate your drill file to the ''lingua franca'' of the mill, [http://www.linuxcnc.org/docview/html/gcode_overview.html G code].
 
* How do I secure my work piece when milling?  Currently, you have to simply tape it down with masking/painter's tape.  Eventually, a better system will be devised.  If you have ideas about what such a ''better system'' might look like, please contact [[User:Mysterious Paul|Paul Kerchen]]!
 
* How do I secure my work piece when milling?  Currently, you have to simply tape it down with masking/painter's tape.  Eventually, a better system will be devised.  If you have ideas about what such a ''better system'' might look like, please contact [[User:Mysterious Paul|Paul Kerchen]]!
 +
* How fast is the spindle on the Dremel tool?  It's variable from 5,000 to 35,000 RPM.
  
  
Last edited: [[User:Mysterious Paul|Mysterious Paul]] 18:33, 30 September 2011 (UTC)
+
Last edited: [[User:Mysterious Paul|Mysterious Paul]] [[User:Mysterious Paul|Mysterious Paul]] 00:38, 3 October 2011 (UTC)
  
 
}}
 
}}

Revision as of 20:38, 2 October 2011


DIY Lil' CNC

A three-axis CNC-controlled Dremel tool

Basic Info

  • Ownership: Paul Kerchen (100%)
  • Location: In the center of the shop near the Torquecut.
  • What it looks like:

DIYLILCNC.jpg

Manufacturer Information

  • Make/Model: Built from DIYLILCNC plan version 1.0.3; the Dremel tool is a 300 Series.
  • Part Number: not specified

Documentation

not specified

Rules

You must contact the owner about getting an account on the linux box that runs the machine.

Instructions

  1. Generate G code
  2. Load G code into AXIS (or one of the other front-ends).
  3. Secure workpiece
  4. Cut
  5. Profit!

Other References

DIY LIL CNC site

Maintenance

There is no routine maintenance required. When you're done with it, be sure to power down the controller box AND the linux box (it doesn't automatically power down on shutdown).

Due to an oversight while building it (forgot to put a flat on the bar that the set screw screws into), the y-axis pulley may become loose over time. If this happens, you'll need to remove the access panel on the y-axis uprights and tighten the set screw.

Things that Need to be Done

  • Build a better workpiece holder
  • Tie into shop dust collector

FAQs

  • Can I mill printed circuit boards on this thing? Hasn't been done yet, but should be possible.
  • Can I drill printed circuit boards on this thing? Yes! Basically, you just need to translate your drill file to the lingua franca of the mill, G code.
  • How do I secure my work piece when milling? Currently, you have to simply tape it down with masking/painter's tape. Eventually, a better system will be devised. If you have ideas about what such a better system might look like, please contact Paul Kerchen!
  • How fast is the spindle on the Dremel tool? It's variable from 5,000 to 35,000 RPM.


Last edited: Mysterious Paul Mysterious Paul 00:38, 3 October 2011 (UTC)