Difference between revisions of "DesignJet 330"
(moved drivers into our wiki)
m (moved HOWTO use the Plotter to HOWTO use the DesignJet 330: Because "plotter" is vague, and may soon refer to more than one machine, at which time that page can become disambiguation.)
Revision as of 14:40, 18 December 2012
Setting it up
The plotter is an HP DesignJet 330. It is connected to the network using an HP JetDirect EX interface. The printserver's IP address is 10.13.0.50. Please don't change the printserver's IP address or configuration, it is not at fault.
With a Mac
Not sure about Macs. Based upon what's in the Use the Printer HOWTO, this seems pretty straightforward. Just know that "port 9100" is the protocol to use, and if it gives you a choice between PS and HPGL, use HPGL.
On a Windows box, you need to ignore the temptation to click "add a network printer", and instead, "add a local printer", then "create a new port", then port type "standard tcp/ip port", then enter 10.13.0.50, and everything else should be sensible.
HP DesignJet 330 drivers exist for Windows XP, but you must use the "HP DesignJet 330 (E/A0)" driver. The "D" driver only supports 24". The "E" driver supports 36" paper.
Since this is an older plotter, HP is no longer writing the drivers for Vista and later versions of Windows. However, there is a set of drivers available for Vista and Windows 7 here:File:Pl532en.zip Use them at your own risk!
How Much Does it Cost?
The cheapest HP plotter paper is about $0.15 a foot. Throw some money in one of the jars when you're done. :)
Loading Roll Paper
First, do you need to? If the plotter is off, and it looks like the paper is loaded, turn it on. After a few minutes of self-testing and moving the paper around, if the lights settle on Plain, Normal, Ready, and Roll you're good. If not:
When the Load Paper light is on solid, insert the end of the paper until you feel a stop and the plotter starts to pull it in. When it stops, the Load Paper light will flash. Open the cover and you'll see it lift the guide bar. Flip the green handle on the right down to release the rollers. Align the edges of the paper so it feeds straight in. Slide the paper so that the right edge is over the punched slots on the metal edge where the paper feeds in. Flip the green lever back up to lock the paper in place. Close the lid. The plotter will pull the paper back in but the edge will still be exposed. Wait for the Ready light to stop blinking. You're done!
Loading Sheet Paper
Please see the manual until it can be tested and summarized here.
- The printer does not have the right parts to mount large rolls of paper, and thus the rolls do not turn freely, so remember to unroll as much paper as is needed to complete your print and avoid a jam. Do this by grasping the paper on both sides and pulling down.
- Turn on the printer. Always check that the printer's ready light is on or blinking. If not, press "Continue Printing" until it is lit.
- In your software select the HP DesignJet 330 E/A0 printer. Press the button to access the printer setup form from within your software. Set the "Roll Size" to "36 Inch Roll". Press the "More Sizes" button and set a custom width and height for the banner you want to print.
- Return to your software and print. If it does not print, verify that the printer's ready light is blinking or lit. If blinking it is still spooling. If the light is not lit, press the "Continue Printing" button.
- When the print is done use the built in cutter to cut the page. After the page is cut move the cutter back to the left. You will need to press the "Continue Printing" button to retract the paper and prepare the printer for the next print.
When You're Done
Before you walk away, make sure that the printhead is "parked" on the left side. If an error occurs during plotting, it will sometimes stay out over the paper. Leaving it this way will allow the printhead to dry out and clog. To check, just lift the hood from the center and see if the printhead is over in the well on the left side. If not, power-cycle the plotter and it will both clear the error and park the printhead.
For More Information
The user manual for the printer is available here: http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/bpp02419/bpp02419.pdf