Difference between revisions of "Kiln Zone"
(→Kiln Trained Users)
|Line 4:||Line 4:|
== Kiln Trained Users ==
== Kiln Trained Users ==
Terry W. - Warden
== KilnZone Rules ==
== KilnZone Rules ==
Revision as of 09:58, 9 June 2013
Kiln Trained Users
- Terry W. - Warden
- Matt Oehrlein - Trainer
- Christine Osinski - Trainer
- Matt A
1) I3 KilnZone training is required to operate KilnZone equipment. A list of Trained Users is below.
2) When not firing, all private materials and components need to be removed to member's storage. The metal rack is for PUBLIC materials only.
3) Use Boron Nitride for public molds. Use Kiln paper for Kiln floor.
4) Clean or apply KilnWash or Boron Nitride OUTSIDE. No Exceptions. ALWAYS use a mask.
5) When using glass powder and other materials of 100 Micron or less, use a mask. And don't work near other people. (Farther than 20' and near ventilation if possible).
6) Do Not open a working Kiln unless you are the current user or there is an emergency.
6) If you are using a Kiln and need to leave the building, Make sure Your name and cell # is on the KILN IN USE Whiteboard and the Kiln In Use Side is outward.
7) Do not put cardboard or paper in the cage. Plastic is OK if more than 18" from the Kiln.
8) ABSOLUTELY NO FLAMMABLES OR PRESSURIZED CONTAINERS IN THE CAGE.
IN CASE OF EMERGENCY
1) If needed call 911.
2) If possible and effective, turn off Programmable Controller with green switch.
3) Else, if possible turn OFF Kiln 1 by turning all 3 knobs on Kiln 1 to ZERO. You should hear a click and see the red light go out.
3) To contain fire, if necessary, use the fire extinguisher located at KilnZone.
4) Call current user at the cell number located on the clip board on the gate of the KilnZone.
Kiln and Glass Casting Classes
Starting 5/29/13 We will have Kiln Training and Glass Casting class almost every Wed at 7PM-9PM for the foreseeable future. Members only. Bring your own mask, N95 or better. Materials will be supplied. No fee. No Walkons. Sign Up by editting this wiki. About 5-6 members per class. Classes Lock down at 5PM of the day prior.
5/29 Class 7PM FULL/CLOSED
6/5 Class 7PM OPEN
- Mike F [and possibly wife]
- Tony K
- Christine O.
- Madeleine B
- Jeff Bannow
6/12 NO CLASS DUE TO RED BULL
6/19 Class 7PM OPEN
- Devon T
- Chris P
6/26 Class 7PM OPEN
- Justin T
How to Program the Kiln Controller
by Terry W.
Step 1) Turn ON controller with Green button. You should see the current temp in PV display.
Step 2) Push the SET button. You should see PASS in the PV display and 0000 in the SV display.
Step 3) Our convention will be > for the rightward arrow button, ^ for the upward and v for the downward, since I can't type that one. Use >, ^, and v to type in 2000 and hit SET.
You will see in books on glass, things called firing schedules. They look like this:
You read that as a set of instructions:
Ramp up the temperature from room temp to 1250F at a rate of 300F per hour.
THEN hold 1250F for 30 minutes.
THEN ramp from there to 1420F at a rate of 300F per hour.
THEN hold it for 30-60 minutes.
THEN ramp as fast as you can from there to 960F
THEN hold it for 90 minutes
THEN ramp at 50F/hr to 800F
SKIP holding it.
THEN ramp at 100F/hr to 600F
THEN turn it OFF and don't open the kiln until Room Temp (No Venting).
Your Kiln Controller needs to be programmed in a series of steps. Each steps has 3 attributes, C,T,Sv. So your list of instructions will look like
Let me define what each of those are.
C is the PID setting we use. We always use PID#1, which I have preprogrammed into the controller. Please do NOT change PID#1.
T is time, in minutes. More later.
Sv is a target temperature in F. I believe Sv is short for “Set Value”. And Pv is Present Value....of what you are trying to control, in our case Temp F.
So from our example
C1=0001, T1, Sv1=0070 (room temp)
C2=0001, T2, Sv2=1250
Now Let me explain what T is. T1 is supposed to be the time (in minutes) we are telling the controller to get from Sv1 to Sv2.
So our programming looks like this:
C1=0001, T1=240, Sv1=0070 (room temp)
C2=0001, T2=30, Sv2=1250
C3=0001, T3= 60 , Sv3=1250
Note that I am rounding to the nearest half hour because kiln work isn't that fussy ...until you get to Pate de Verre, which is not covered in this lesson.
Once you have put in all steps, scroll up to END and hit SET. This enters your program. The controller will keep it, even if switched off.
Once programmed, you can
1) Make sure the Thermocouple (yellow plug) is plugged into the yellow socket (check polarity).
2) Make sure the data signal (blue cat5e wire) is plugged into the Controller and the Relay Box.
3) Make sure the Relay box is plugged into the wall and the circuit breaker is set to ON.
4) Roll the cart OUT of the cage.
5) Make sure the top of the kiln is plugged into the bottom.
6) Make sure all 3 knobs are set to 10 (or to 11 if you are a Spinal Tap fan).
7) Make sure the Kiln is plugged into the Relay Box.
8) Turn on the Controller with the Green Switch.
9) Hit the > key and you ???
- Kiln (i3)
- Kiln2 (i3)
- Relay Box/Programmable Controller 1 (i3)
- Web-based Programmable Controller 2 (i3)
- Several Glass Casting Mold (TW)
- Several Slumping Molds (i3)
- All Kiln Furniture (i3)
Kiln Sitter (Not Installed)