Search by property

This page provides a simple browsing interface for finding entities described by a property and a named value. Other available search interfaces include the page property search, and the ask query builder.

List of results

Jet Drum Sander + (Add outfield tables)
Stop the Bleed Kit + (Add pictures, fill out this page.)
Embroidery Machine - Husqvarna Designer SE + (Better documentation and investigation int … Better documentation and investigation into the design/execution toolchain--scheduled to be handled by the Coordinators.Coordinators: Regularly check bobbin cutting blade. Order new part from repair shop if damaged.Coordinators: Regularly check for nicks/scratches in needle plate. Sand out as necessary. Similarly, nicks in feet should be sanded lightly to reduce the burrs.Kevin: Rewrite maintenance page as maintenance + troubleshooting; add link to Husqvarna troubleshooting section of manual (http://www.husqvarnaviking.com/SiteMedia/Products/Machines/Support/Designer_SE_Troubleshooting_EN.pdf).Anyone: List available hoop sizesN.pdf). Anyone: List available hoop sizes)
Dayton 24" Brake + (Build a stand and bolt it to the floor)
Welding Table + (Build or acquire proper storage for the various tools and components that go with the table.)
Mitre Saw + (Buy a better one. Supplement with a cold saw.)
Powder Coating Gun + (Buy a more professional, non horror fright gun.)
Parts Washer + (Buy Fluid, we used 5-10 gallons of purple power last time, research concentration needed and dilute to appropriate cleaning ratio. Add a oil pan warmer to heat cleaning liquid.)
Singer "Ultralock" Serger 14U34 + (Buy it a new power cord/pedal, because it must have left.)
Acer 1440G Lathe + (Center Tailstock)
UV Cure Toaster Oven + (Check bulbs, one of them might be burned out.)
Arburg 221-75-350 + (Connect power and air lines)
ArtSign JSM-40U Laser Cutter + (Controller needs fixing/replacement. Foof/Brian need a couple round tuits.)
Panel Lights + (Detailed instructions)
2 Post Auto Lift + (Determine maintenance schedule and populate this section better. Determine bolt torque requirements and obtain appropriate wrench if necessary.)
Avid CNC + (Essential stuff * Order pendant)
Sewing HVAC + (Find and install line set covers. Seal hole for line set in exterior wall.)
Re:load Pro + (Find out how this works (See PDF link in "Documentation"))
Edlund Drill Press + (Fix tensioner)
Singer 660 A202 Industrial Sewing Machine + (Fix timing. August 2023)
Brother cs6000i sewing machine (Percy) + (Get a power cord as it's missing. buy: Bobbin (4) https://www.brother-usa.com/products/sa156 (One is on machine.) SA156 buy: Walking Foot SA140)
Kenmore Model 54 Sewing Machine (Violet) + (Get new belt)
Lightbulb load-box + (Grab a photo! Add a fan and intake/exhaust grilles?)
Badger Universal Model 360 Airbrush + (I need to take more photos and post them along with a link or two to some sort of airbrush how-to. I've never used one myself, so until I've accessed that content and played around with the airbrush, this page will remain a stub.)
Walter's CNC Plasma Cutter + (In the final stages of being set up. Tool chain still needs to be defined.)

LED Matrix Display + (Inoperative and needs repair as of 2026-06-24.)

Rhino CNC Lathe + (It is currently out of the shop for a retrofit. the controller is being replaced to allow it to run from Mach 3.)
Babylock Evolve Serger + (Jan to develop training program Make training kit Make machine dust cover Signage for cover Develop user fee structure)
RFID entry system + (Known esp rfid bugs (not reported to esp rfid because making test cases takes time) * a user badging in can scan as the previous user occasionally, so it says bad pin * doors crash a lot when reading the user list)
LED Wall Display + (Make a nicer wooden housing. Implement display of rotating messages)
OpenEVSE + (Maybe replace the i2c cable with something better. There are parts to build another one that has not been completed.)
Drafting/DrawingTableWithPowerLift + (Might need plugging in.)
Husqvarna Viking Sewing Machine Emerald 116 + (Missing parts were purchased so machine could be used and have been tested. No other tasks due at this time.)
Tacsew T175 Blindstitch Machine + (Need spool pin Need knee lever)
AllRounder 150 + (Need to have controller built)
Juki DDL-5550N-7 Industrial Sewing Machine + (New bobbin winder. Install manual knee lift to replace defective servo.)
3Doodler + (None.)
Furnace: A North + (Presently powered from the row-2 light circuit. Fix that?)
PCB Mill + (Procure a full set of the mill, routers, and drills. '''Restore spindle motor driver board to functionality''')
X-Tronic 4000 Hot Air Rework Station + (Pump is broken)
Cyclonic Dust Collection System + (purchased use New Rotary AirLock*)
Baby Lock Imagine Serger + (Replace machine.)
Bridgeport Mill + (replace or repair light (droops) wire in the power feed, light, and DRO so the wires are not in the way run air line to the machine for coolant mister repair coolant mister (droops) buy and add pneumatic drawbar buy and add drill-powered knee)
Rockwell Drill Press + (scrap.)
3D Printer - FormLabs Form2 PerfectWhale + (Sell machine)
Dishwasher + (Set up and get working.)
Kenmore Dyemaster 2000 + (Setup and get running. Looks like a washing machine.)
Embroidery Machine - Husqvarna Diamond Deluxe + (Signage for hard cover)
Tent + (Some of the bent pieces could be replaced. Probably could use a good wash.)
Salt Godbox + (Tasks: * UPGRADE SALT ** [[User:AstraLuma|Jamie Bliss]] … Tasks:* UPGRADE SALT** [[User:AstraLuma|Jamie Bliss]]: Fix SpiroFS* change hypervisor on [[hardac]]?* Wireguard?** Use [[skynet]] as endpoint** Web VM <-> space permanent link** member VPN instead of L2TP?* Monitoring VM** Grafana** Telegraf** SNMP** syslog server** logtail** Maybe repurpose [[mcclellan]]* So many docs* Actually train a few other people on how to use the systemrain a few other people on how to use the system)
Media Workstation Prime + (The hard drive is also the boot and instal … The hard drive is also the boot and installation drive, which makes it feel sluggish by 2026 standards. Consider moving boot and program files to an SSD of 0.5-1 TB capacity.Case and CPU fans are incredibly noisy under moderate load. Consider upgrading to quieter fans (Noctua?).Needs case screws to attach the side panel.eeds case screws to attach the side panel.)